High-Pressure Bi-Directional Hydraulic Piston Seal
O-ring-energized cap seal design. The specially designed hard wearing, 60 shore D, self-lubricated polyurethane cap is much easier to install than PTFE cap seals and provides high extrusion resistance. Further, the design provides a fluid reservoir between the two beveled sealing lips which retains system fluid, resulting in reduced running and breakaway friction. Beveled sealing lips for maximum fluid sealing ability protect against extrusion during pressure spikes up to 10,000psi. The small axial seal height reduces piston height, weight and cost. Retro fits seals of similar design.
mineral oil-based fluids, fire-resistant water-based hydraulic fluids including HFA and HFB, sea water, biodegradable fluids, vegetable oils, bio-diesels, and most modern hydraulic fluids
Duralast 4403
5,000psi (350bar)
8,000psi (520bar)
-22°F to 260°F (-30°C to 125°C)
1.6ft/s (0.5m/s)
same as Duralast 4203
Additional standard materials available: High-performance polyurethanes, low- and high-temperature, FDA-compliant seal material grades, engineered thermoplastics, Hytrel®, NBR (Nitrile), FKM, Viton®, HNBR, EPDM, Aflas®, Silicone, and proprietary specialized Duralast™, Duraloy™, and Permachem™ materials.
Important Note: Maximum values above depend on extrusion gap, clearances, seal material, media, temperatures, pressures, surface speed, dynamic running surface finish and working environment. Seals cannot be operated at their upper ratings at the same time. Pressure ratings can be increased by reducing clearances. For pressure above specified operating pressure, please contact engineering@ahpseals.com
Size Table (Inch)The standard range sizes listed below are the preferred sizes for new design applications. Seals are available for any bore size in 0.001inch increments, including functional range. Additionally, we offer any other seal size as required.
A
Bore Diameter
CS
Cross-Section
D
Groove Diameter
B*
Piston Diameter
Tolerance
L
Groove Width
C
R1
R
Standard Range
Functional Range
Tolerance
D=
B=
D,B
Tol.+0.008/-0
min.
max.
max.
0.312 - 0.564"
0.300 - 0.599"
+0.001/-0
0.097
A - 0.194
A - 0.024
+.000/-.001
0.087
0.045
0.015
0.006
0.565 - 1.499"
0.550 - 1.599"
+0.002/-0
0.148
A - 0.296
A - 0.024
+.000/-.002
0.126
0.050
0.025
0.008
1.500 - 3.124"
0.550 - 12.000"
+0.003/-0
0.217
A - 0.434
A - 0.027
+.000/-.003
0.165
0.070
0.025
0.008
3.125 - 5.249"
1.500 - 18.500"
+0.003/-0
0.305
A - 0.610
A - 0.029
+.000/-.003
0.248
0.100
0.035
0.008
5.250 - 12.499"
3.000 - 26.500"
+0.004/-0
0.414
A - 0.828
A - 0.030
+.000/-.004
0.320
0.130
0.035
0.008
12.500 - 26.599"
5.000 - 26.500"
+0.005/-0
0.483
A - 0.966
A - 0.034
+.000/-.005
0.320
0.130
0.035
0.008
26.600 - 40.124"
10.000 - 50.000"
+0.007/-0
0.552
A - 1.102
A - 0.045
+.000/-.007
0.375
0.150
0.040
0.012
40.125 - 72.500"
20.000 - 72.500"
+0.009/-0
0.748
A - 1.496
A - 0.050
+.000/-.009
0.543
0.170
0.050
0.012
> 72.500"
consult with Ahpseals engineering
* Based on using wear rings. For pressure above 3,800psi or diameter 26,500", please contact engineering for clearances. Surface finish: rod (A) Ra 4-12µin – Static (D,L) Ra max. 32µin. See Technical Info for more specific information.
Size Table (Metric)The standard range sizes listed below are the preferred sizes for new design applications. Seals are available for any bore size in 0.01mm increments, including functional range. Additionally, we offer any other seal size as required.
A
Bore Diameter
Tol. H8
CS
Cross-Section
D
Groove Diameter
Tol. h9
B*
Piston Diameter
Tol. h9
L
Groove Width
C
R1
R
Standard Range
Functional Range
D=
B=
Tol.+0.20/-0
min.
max.
max.
8.00 -14.99
8.00 - 30.00
2.45
A - 4.90
A - 0.60
2.20
1.20
0.40
0.15
15.00 - 39.99
15.00 - 80.00
3.65
A - 7.50
A - 0.60
3.20
1.30
0.60
0.20
40.00 - 59.99
25.00 - 200.00
5.35
A - 10.70
A - 0.70
4.20
1.80
1.00
0.20
60.00 - 199.99
25.00 - 260.00
7.55
A - 15.10
A - 0.74
6.30
2.50
1.30
0.20
200.00 - 259.99
75.00 - 700.00
10.25
A - 20.50
A - 0.76
8.10
3.30
1.80
0.20
260.00 - 674.99
125.00 - 675.00
12.00
A - 24.00
A - 0.86
8.10
3.30
1.80
0.20
675.00 - 999.99
250.00 - 1200.00
14.00
A + 28.00
A + 1.00
9.50
3.80
2.50
0.30
1000.00 - 1850.00
500.00 - 1850.00
19.00
A + 38.00
A + 1.50
13.80
4.20
3.00
0.30
> 1850.00
consult with Ahpseals engineering
* Based on using wear rings. For pressure above 260bar or diameter 675mm, please contact engineering for clearances. Surface finish: bore (A) Ra 0.1-0.3µm – Static (D,L) Ra max. 0.8µm. See Technical Info for more specific information.
