High-pressure, low-speed internal rotary/swivel seal
Small -footprint internal seal designed for rotary couplings/distributors.
The one-piece elastomer design makes it easier to fit in multi-port units than traditional PTFE-based seals. This seal is made of a high-performance wear-resistant elastomer designed to separate two different media. This seal handles up to 5,000*psi. Small quantities are available in 1 to 3 days.
Size Table (Inch)Standard sizes listed below are preferred sizes for new design applications; however, we offer any other seal size as required.Seals are available for any shaft diameter size in 0.001 inch increments without tooling charges, including Functional Range.
A
Shaft Diameter
CS
Cross-section
D
Bore
Diameter
B
Diameter
Tolerance
L
C
R1
R
Standard Range
Functional Range
Tolerance
**
D=
B=
D, B
Tol.+0.008/-0
min.
max.
max.
0.250-0.749"
0.250 - 5.100"
+0/-0.0015
0.096
A + 0.193
A + 0.002
+0.0015/-0
0.087
0.040
0.015
0.005
0.750-1.499"
0.390 - 9.640"
+0/-0.002
0.148
A + 0.295
A + 0.003
+0.002/-0
0.126
0.060
0.020
0.005
1.500 - 7.499"
0.750 - 18.000"
+0/-0.003
0.217
A + 0.433
A + 0.004
+0.003/-0
0.165
0.080
0.040
0.005
7.500 - 12.999"
1.500 - 25.750"
+0/-0.004
0.305
A + 0.610
A + 0.005
+0.004/-0
0.248
0.090
0.050
0.005
13.000 - 25.599"
4.750 - 25.750"
+0/-0.005
0.413
A + 0.826
A + 0.006
+0.005/-0
0.319
0.130
0.070
0.005
25.600 - 40.999"
25.000 - 63.000"
+0/-0.006
0.551
A + 1.102
A + 0.008
+0.006/-0
0.375
0.150
0.100
0.005
41.000 - 63.000"
consult AHPSeals engineering
**Standard cross-sections(CS) listed and non-standard sizes can be provided for any shaft size up to 63 inches.**For heavy-duty applications that include; frequent pressure spikes; vibrations; and thermocycling, it is recommended to move up one size in the CS. Surface finish: Shaft (A) plunge ground, zero lead, Ra 8-16µin using elastomer seals, Ra 6-12µin using PTFE seals.Housing (D,L) Ra 32-63µin, shaft material hardness 55-65RC. See Technical Info for more specific information.
Size Table (Metric)Standard sizes listed below are preferred sizes for new design applications; however, we offer any other seal size as required.Seals are available for any shaft diameter size in 0.01 mm increments without tooling charges, including Functional Range.
A
Shaft Diameter (mm)
Tol. h8
CS
Cross-section
D
Bore Diameter
Tol. H8
B
Diameter
Tol. H8
L
C
R1
R
Standard Range
Functional Range
**
D=
B=
Tol.+0.20/-0
min.
max.
max.
5.50 - 18.99
5.50 - 130.00
2.45
A + 4.90
A + 0.05
2.20
1.00
0.40
0.12
19.00 - 37.99
10.00 - 245.00
3.75
A + 7.50
A + 0.07
3.20
1.50
0.60
0.12
38.00 - 189.99
19.00 - 455.00
5.50
A + 11.00
A + 0.10
4.20
2.00
1.00
0.12
190.00 - 329.99
39.00 - 651.00
7.75
A + 15.50
A + 0.12
6.30
2.30
1.30
0.12
330.00 - 650.99
120.00 -651.00
10.50
A + 21.00
A + 0.15
8.10
3.30
1.80
0.12
651.00 - 1049.99
630.00 - 1600.00
14.00
A + 28.00
A + 0.20
9.50
3.80
2.50
0.12
1050.00 - 1600.00
consult AHPSeals engineering
**Standard cross-sections (CS) listed and non-standard sizes can be provided for any shaft size up to 1600 mm. **For heavy-duty applications that include; frequent pressure spikes; vibrations; and thermocycling, it is recommended to move up one size in the CS. Surface finish: Shaft(A) plunge ground, zero lead, Ra 0.2-0.4µm using elastomer seals, Ra 0.15-0.30µm using PTFE seals Housing (D,L) Ra 0.8-1.6µm. Shaft material hardness 55-65RC. See Technical Info for more specific information.