Bi-Directional Low-Friction Hydraulic Rod Seal

S93


Bi-Directional Low-Friction Hydraulic Rod Seal

O-ring-energized seal providing smooth movement, low friction and long service life over a wide range of light- to medium-duty applications.  The small axial seal height reduces gland height, weight and cost. Commonly used in hydraulic presses, machine tools, injection molding machines and mobile hydraulics.




Operating Range
MaterialOperating Pressure up toMaximum Pressure up toTemperatureSurface Speed up toFluid, Media Compatability
Permachem 66433,800psi (260bar)5,000psi (350bar)-40°F to 400°F (-40°C to 210°C)13ft/s (4m/s)mineral oil-based fluids, fire-resistant water-based hydraulic fluids including HFA and HFB, biodegradable fluids, vegetable oils, bio-diesels, and most modern hydraulic fluids
Permachem 61505,000psi (350bar)6,000psi (420bar)-40°F to 400°F (-40°C to 210°C)13ft/s (4m/s)same as Permachem 6643
Additional standard materials available: PTFE, filled Teflon®, engineered thermoplastics, high-performance polyurethanes, NBR (Nitrile), FKM, Viton®, HNBR, EPDM, Aflas®, Hytrel®, Silicone, low- and high-temperature, FDA-compliant seal material grades and proprietary specialized Duralast™, Duraloy™, and Permachem™ materials.
Important Note: Maximum values above depend on extrusion gap, clearances, seal material, media, temperatures, pressures, surface speed, dynamic running surface finish and working environment. Seals cannot be operated at their upper ratings at the same time. Pressure ratings can be increased by reducing clearances. For pressure above specified operating pressure, surface speed above 5ft/s (1.3m/s), or for any advice, please contact engineering@ahpseals.com
Size Table (Inch)
A
Rod Diameter
CS
Cross-Section
D
Groove
Diameter
B*
Gland
Diameter
Tolerance
L
Groove Width
C
R1
R
Standard Range
Functional Range
Tolerance
D=
B=
D,B
Tol.+0.008/-0
min.
max.
max.
0.312 - 0.624"
0.300 - 1.500"
+0/-0.001
0.097
A + 0.194
A + 0.024
+0.001/-0
0.087
0.080
0.015
0.006
0.625 - 1.624"
0.560 - 3.500"
+0/-0.002
0.143
A + 0.286
A + 0.026
+0.002/-0
0.126
0.050
0.015
0.006
1.625 - 3.249"
0.750 - 8.000"
+0/-0.003
0.210
A + 0.420
A + 0.027
+0.003/-0
0.165
0.070
0.020
0.006
3.250 - 5.374"
1.500 - 10.500"
+0/-0.003
0.297
A + 0.594
A + 0.029
+0.003/-0
0.248
0.100
0.040
0.008
5.375 - 12.999"
5.000 - 26.500"
+0/-0.004
0.403
A + 0.806
A + 0.030
+0.004/-0
0.319
0.130
0.050
0.008
13.000 - 26.500"
10.000 - 40.000"
+0/-0.005
0.473
A + 0.946
A + 0.034
+0.005/-0
0.319
0.130
0.050
0.008
> 26.500"
consult with Ahpseals engineering
* Based on using wear rings. For pressure above 3,800psi, please contact engineering for clearances. For rod diameter below 0.475 inch, open or split housing is recommended. Surface finish: rod (A) Ra 4-12µin – Static (D,L) Ra max. 32µin. See Technical Info for more specific information.

Seal Size Selector – Request a Quote

  • Enter shaft, rod or bore diameter
  • If recommended size is not feasible, please enter your preferred dimensions
  • If recommended size is not feasible, please enter your preferred dimensions
Back to Products page
Seal Housing Drawing