O-ring-energized economical bi-directional light- to medium-duty hydraulic or pneumatic seal. The thinner PTFE cap is designed to better respond to low-pressure sealing.
mineral oil-based fluids, fire-resistant water-based hydraulic fluids including HFA and HFB, biodegradable fluids, vegetable oils, bio-diesels, and most modern hydraulic fluids
Permachem 6150
5,000psi (350bar)
6,000psi (420bar)
-40°F to 400°F (-40°C to 210°C)
13ft/s (4m/s)
same as Permachem 6643
Additional standard materials available: PTFE, filled PTFE®, engineered thermoplastics, high-performance polyurethanes, NBR (Nitrile), FKM, Viton®, HNBR, EPDM, Aflas®, Hytrel®, Silicone, low- and high-temperature, FDA-compliant seal material grades and proprietary specialized Duralast™, Duraloy™, and Permachem™ materials.
Important Note: Maximum values above depend on extrusion gap, clearances, seal material, media, temperatures, pressures, surface speed, dynamic running surface finish and working environment. Seals cannot be operated at their upper ratings at the same time. Pressure ratings can be increased by reducing clearances. For pressure above specified operating pressure, surface speed above 5ft/s (1.3m/s), or for any advice, please contact engineering@ahpseals.com
Size Table (Inch)Standard range sizes listed below are preferred sizes for new design applications. Seals are available for any rod diameter size in 0.001 inch increments, including functional range. Additionally, we offer any other seal size as required.
A
Rod Diameter
CS
Cross-Section
D
Groove
Diameter
B*
Gland
Diameter
Tolerance
L
Groove
Width
C
R1
R
Standard Range
Functional Range
Tolerance
D=
B=
D,B
Tol.+0.008/-0
min.
max.
max.
0.125 - 0.249"
0.125 - 1.500"
+0/-0.001
0.072
A + 0.144
A + 0.001
+0.001/-0
0.079
0.080
0.015
0.006
0.250 - 0.314"
0.250 - 3.500"
+0/-0.001
0.086
A + 0.172
A + 0.002
+0.002/-0
0.079
0.080
0.015
0.006
0.315 - 0.709"
0.300 - 4.000"
+0/-0.002
0.118
A + 0.236
A + 0.002
+0.002/-0
0.112
0.050
0.015
0.006
0.710 - 1.499
0.700 - 5.500"
+0/-0.003
0.150
A + 0.300
A + 0.003
+0.002/-0
0.149
0.070
0.020
0.006
1.500 - 4.499"
1.500 - 8.000"
+0/-0.004
0.246
A + 0.491
A + 0.003
+0.003/-0
0.221
0.100
0.040
0.006
4.500 - 5.879"
4.000 - 10.000"
+0/-0.004
0.297
A + 0.593
A + 0.004
+0.004/-0
0.297
0.130
0.050
0.006
5.880 - 26.499"
4.000 - 26.500"
+0/-0.005
0.359
A + 0.718
A + 0.005
+0.005/-0
0.297
0.130
0.050
0.006
> 26.500"
consult with Ahpseals engineering
*Based on using no wear rings. If using wear rings, please contact engineering for max. pressure and clearances. For rod diameter below 0.475 inch, open or split housing is recommended.
Surface finish: rod (A) Ra 4-12µin – Static (D,L) Ra max. 32µin. See Technical Info for more specific information.
Size Table (Metric)Standard range sizes listed below are preferred sizes for new design applications. Seals are available for any rod diameter size in 0.01 mm increments, including functional range. Additionally, we offer any other seal size as required.
A
Rod Diameter Tol. h8
CS
Cross-Section
D
Groove
Diameter
Tol. H9
B*
Gland
Diameter
Tol. H9
L
Groove
Width
C
R1
R
Standard Range
Functional Range
D=
B=
Tol.+0.20/-0
min.
max.
max.
3.00 - 6.99
3.00 - 40.00
2.00
A + 4.00
A + 0.03
2.20
0.80
0.30
0.15
7.00 - 24.99
7.00 - 90.00
3.10
A + 6.20
A + 0.05
3.20
1.10
0.30
0.15
25.00 - 39.99
25.00 - 150.00
3.75
A + 7.50
A + 0.05
3.80
1.50
0.50
0.15
40.00 - 114.99
40.00 - 200.00
6.25
A + 12.50
A + 0.07
5.60
1.80
1.00
0.15
115.00 - 149.99
100.00 - 250.00
7.50
A + 15.00
A + 0.08
7.50
2.00
1.30
0.15
150.00 - 670.00
100.00- 670.00
9.10
A + 18.20
A + 0.09
7.50
2.00
1.30
0.15
> 670.00
consult with Ahpseals engineering
*Based on using no wear rings. If using wear rings, please contact engineering for max. pressure and clearances. For rod diameter below 12mm open or split housing is recommended.
Surface finish: rod (A) Ra 0.1-0.3µm – Static (D,L) Ra max. 0.8µm. See Technical Info for more specific information.