Single-lip PTFE rotary shaft seal for higher sealability

SB12


Single-lip PTFE rotary shaft seal for higher sealability

This seal design incorporates a formed seal lip with an “elf-toe” design offering extended runout and improved sealability, especially for abrasive media or gaseous media, due to the slightly higher lip load. It is capable of handling extreme temperature, abrasive media, high surface speeds, low to medium pressures, and can even run dry.  The soft seal OD eliminates damage to housings manufactured from expensive metals.  An integrated O-ring on the OD of the seal serves as an anti-rotation device and provides positive static sealing between the seal and the bore.  It is typically used as a highly sealable solution for gearboxes, submersible pumps/motors and mixers.  Small quantities are available in 2-4 days.




Operating Range
MaterialContinuous PressureMax.Pressure SpikeTemperatureSurface SpeedApplicationDry-runPV-Rating
Permachem 6233110psi (7.6bar)300psi (20bar)-58 to 400°F (-50 to 200°C)Up to 4,000 fpm (20m/s)standard oil lubrication, high waterbased fluidsYES5
Permachem 6235110psi (7.6bar)300psi (20bar)-58 to 400°F (-50 to 200°C)Up to 4,000 fpm (20m/s)Soft shaft material, gaseous media, FDA compliantYES5
Duraloy 4736110psi (7.6bar)300psi (20bar)-58 to 400°F (-50 to 200°C)Up to 4,000 fpm (20m/s)low wear and abrasion, long service lifeYES5
Size Table (Inch)Standard Range sizes listed below are preferred sizes for new design applications; however, we offer any other seal size as required.Seals are available for any shaft diameter size in 0.001 inch increments, including Functional Range.
A
Shaft Diameter
CS
Cross-section

D
Bore Diameter
B
without
wiper lip +/- 0.010
B with
wiper lip +/- 0.010
L
F
C
R
Standard Range
Functional Range
Tolerance
*D=
Tolerance
B=
B=
+0.012/-0
+/-0.010
min.
max.
0.315 - 0.999"
0.315 - 5.000"
+/-0.003
1/4
A + 0.500
+/-.001
A + 0.030
A + 0.120
0.262
0.223
0.070
0.020
1.000 - 5.999"
0.315 - 18.000"
+/-0.003
3/8
A + 0.750
+/-.001
A + 0.030
A + 0.120
0.300
0.255
0.085
0.020
6.000 - 15.999"
0.500 - 26.000"
+/-0.004
1/2
A + 1.000
+/-.002
A + 0.035
A + 0.120
0.375
0.310
0.090
0.030
16.000 - 25.999"
0.500 - 26.000"
+/-0.006
5/8
A + 1.250
+/-.003
A + 0.040
A + 0.1200.512
0.425
0.100
0.030
26.000 - 63.000"
consult with Ahpseals engineering
*Standard cross-sections (CS) listed and non-standard sizes can be provided for any shaft size up to 63 inches. Surface finish: Shaft (A) plunge ground, zero lead Ra 6-12µin - Housing (D,L) Ra max.32µin - Shaft material hardness 55-65RC. Use of installation tool is highly recommended. See Technical Info for more specific information.

Seal Size Selector – Request a Quote

  • Enter shaft, rod or bore diameter
  • If recommended size is not feasible, please enter your preferred dimensions
  • If recommended size is not feasible, please enter your preferred dimensions
Back to Products page
Seal Housing Drawing