VS-S19


Spring-Loaded PTFE Rod Seal

Designed for very low friction, extreme temperature service (cryogenic to high temperature) or chemically aggressive environments. The standard material for the V-spring is 301 stainless steel, other materials available.




Operating Range
MaterialOperating Pressure up toMaximum Pressure up toTemperatureSurface Speed up toFluid, Media Compatability
Permachem xxxx5,000psi (350bar) vacuum10,000psi (700bar)-328°F to 500°F (-200°C to 260°C)33ft/s (10m/s)Various material compound and spring combinations are available for aggressive chemicals, NACE service, chlorine service, cryogenic service, vacuum service, FDA (both contact and non-contact), fugitive emissions, as well as control fluids, hydraulic fluids, dry running in a wide range of gases
Material Permachem xxxx will be selected by AHPSeals to match your operating conditions.
*Important Note: Maximum values above depend on extrusion gap, clearances, seal material, media, temperatures, pressures, surface speed, dynamic running surface finish and working environment. Seals cannot be operated at their upper ratings at the same time. For pressure above 3.000psi (210bar)or temperature above 200°F (95°C), please contact engineering for seal material and hardware specification.
Size Table (Inch)"The standard range sizes listed below are the preferred sizes for new design applications. Seals are available for any rod size in 0.001inch increments, including functional range. Additionally, we offer any other seal size as required.
A
Rod Diameter
CS
Cross- section*
D
Bore
Diameter
B**
Diameter
Tolerances
L
Standard ≤3.000psi
L
Extended >3.000psi
S
C
R
Radius
Standard Range
Functional Range
Tolerance
D=
B=
D, B
Tolerances +0.010/-0min.
min.
max.
0.125 - 0.249
0.125 - 4.000"
+0/-0.001
1/16
A + 0.125
A + 0.004
+0.001/-0
0.095
0.150
0.050
0.025
0.008
0.250 - 0.874"
0.230 - 6.000"
+0/-0.002
3/32
A + 0.187
A + 0.006
+0.002/-0
0.140
0.180
0.070
0.025
0.015
0.875 - 1.674"
0.335 - 20.000"
+0/-0.002
1/8
A + 0.250
A + 0.008
+0.002/-0
0.185
0.235
0.090
0.030
0.015
1.675 - 4.999"
0.750 - 30.000"
+0/-0.002
3/16
A + 0.375
A + 0.012
+0.002/-0
0.280
0.330
0.110
0.060
0.015
5.000 - 21.999"
1.575 - 71.000"
+0/-0.004
1/4
A + 0.500
A + 0.016
+0.004/-0
0.375
0.475
0.140
0.080
0.015
22.000 - 40.999"
1.575 - 71.000"
+0/-0.005
5/16
A + 0.625
A + 0.020
+0.005/-0
0.460
0.580
0.150
0.110
0.020
41.000 - 71.000"
consult AHPSeals engineering
*Standard cross-sections (CS) listed and non-standard sizes can be provided for any shaft size up to 71 inches. ** Based on using no wear rings, larger clearance required if using wear rings.
Surface finish: Shaft (A) plunge ground, Ra 4-8µin - Housing (D,L) Ra 16-32µin.
Shaft material hardness 55-65RC. See Technical Info for more specific information.

Seal Size Selector – Request a Quote

  • Enter shaft, rod or bore diameter
  • If recommended size is not feasible, please enter your preferred dimensions
  • If recommended size is not feasible, please enter your preferred dimensions
Back to Products page
Seal Housing Drawing