Shop Seals | Shop Seals by AHP Seals

Showing 73–84 of 326 results

FLA
FLA
Elastomeric External Pressure Face Seal

Designed to prevent external pressure or media entering between two faces. This seal has the advantage of staying in the groove, making assembly easier. Available in many different elastomers and thermoplastics dependent on media and operating conditions.

Compare
FLA1
FLA1
Elastomeric External Pressure Face Seal

Designed to prevent external pressure or media entering between two faces. This seal has the advantage of staying in the groove, making assembly easier. Used instead of FLA when vibration is an issue. Available in many different elastomers and thermoplastics dependent on media and operating conditions.

Compare
FLB
FLB
Elastomeric Internal Pressure Face Seal

Designed to prevent internal pressure or media exiting between two faces. This seal has the advantage of staying in the groove, making assembly easier. Available in many different elastomers and thermoplastics dependent on media and operating conditions.

Compare
FLB1
FLB1
Elastomeric Internal Pressure Face Seal

Designed to prevent internal pressure or media exiting between two faces. This seal has the advantage of staying in the groove, making assembly easier. Used instead of FLB when vibration is an issue. Available in many different elastomers and thermoplastics dependent on media and operating conditions.

Compare
GB
GB
High-pressure single-lip oil seal

This seal style is designed to minimize friction and aid in the development of low-noise power steering systems. The solid captured insert leads to reduced friction, increased extrusion resistance, and reduces contamination. Temperature range and fluid resistance can be matched due to correct elastomer and polymer selection.

Compare
HRO
HRO
High misalignment, single-lip oil seal

This is an oil seal designed to operate in environments where the shaft run-out or misalignment are unavoidable. High flexibility of the seal leg allows the sealing lip to remain central to the shaft even under high run-out or eccentricity.

Compare

Internal Pressure Face seal

Designed to prevent internal pressure or media exiting between two faces. This seal is used to seal corrosive media or gases, as well as vacuum conditions. The additional load of the helical spring provides a gas-tight seal even under fluctuating temperature cycles.

Operating Range

Material	Operating Pressure up to	Maximum Pressure up to	Temperature	Surface Speed up to	Fluid, Media Compatability
Permachem xxxx	5,000psi (350bar) vacuum	10,000psi (700bar)	-328°F to 500°F (-200°C to 260°C)	0.3ft/s (0.1m/s) intermitten	vacuum service, aggressive chemicals, NACE service, chlorine service, cryogenic service, FDA (both contact and non-contact), fugitive emissions, as well as control fluids, hydraulic fluids, dry running in a wide range of gases
Material Permachem xxxx will be selected by AHPSeals to match your operating conditions.
*Important Note: Maximum values above depend on extrusion gap, clearances, seal material, media, temperatures, pressures, surface speed, dynamic running surface finish and working environment. Seals cannot be operated at their upper ratings at the same time. For pressure above 3.000psi (210bar)or temperature above 200°F (95°C), please contact engineering for seal material and hardware specification.

Compare

HS-FL6

Internal Pressure Face seal

Operating Range

Material	Operating Pressure up to	Maximum Pressure up to	Temperature	Surface Speed up to	Fluid, Media Compatability
Permachem xxxx	5,000psi (350bar) vacuum	10,000psi (700bar)	-328°F to 500°F (-200°C to 260°C)	0.3ft/s (0.1m/s) intermitten	vacuum service, aggressive chemicals, NACE service, chlorine service, cryogenic service, FDA (both contact and non-contact), fugitive emissions, as well as control fluids, hydraulic fluids, dry running in a wide range of gases
Material Permachem xxxx will be selected by AHPSeals to match your operating conditions.
*Important Note: Maximum values above depend on extrusion gap, clearances, seal material, media, temperatures, pressures, surface speed, dynamic running surface finish and working environment. Seals cannot be operated at their upper ratings at the same time. For pressure above 3.000psi (210bar)or temperature above 200°F (95°C), please contact engineering for seal material and hardware specification.

Compare

HS-FL7

External Pressure Face Seal

Designed to prevent external pressure or media entering between two faces. This seal is used to seal corrosive media or gases, as well as vacuum conditions. The additional load of the helical spring provides a gas-tight seal even under fluctuating temperature cycles.

Operating Range

Material	Operating Pressure up to	Maximum Pressure up to	Temperature	Surface Speed up to	Fluid, Media Compatability
Permachem xxxx	5,000psi (350bar) vacuum	10,000psi (700bar)	-328°F to 500°F (-200°C to 260°C)	0.3ft/s (0.1m/s) intermitten	vacuum service, aggressive chemicals, NACE service, chlorine service, cryogenic service, FDA (both contact and non-contact), fugitive emissions, as well as control fluids, hydraulic fluids, dry running in a wide range of gases
Material Permachem xxxx will be selected by AHPSeals to match your operating conditions.
*Important Note: Maximum values above depend on extrusion gap, clearances, seal material, media, temperatures, pressures, surface speed, dynamic running surface finish and working environment. Seals cannot be operated at their upper ratings at the same time. For pressure above 3.000psi (210bar)or temperature above 200°F (95°C), please contact engineering for seal material and hardware specification.

Compare

HS-FL7

External Pressure Face Seal

Operating Range

Material	Operating Pressure up to	Maximum Pressure up to	Temperature	Surface Speed up to	Fluid, Media Compatability
Permachem xxxx	5,000psi (350bar) vacuum	10,000psi (700bar)	-328°F to 500°F (-200°C to 260°C)	0.3ft/s (0.1m/s) intermitten	vacuum service, aggressive chemicals, NACE service, chlorine service, cryogenic service, FDA (both contact and non-contact), fugitive emissions, as well as control fluids, hydraulic fluids, dry running in a wide range of gases
Material Permachem xxxx will be selected by AHPSeals to match your operating conditions.
*Important Note: Maximum values above depend on extrusion gap, clearances, seal material, media, temperatures, pressures, surface speed, dynamic running surface finish and working environment. Seals cannot be operated at their upper ratings at the same time. For pressure above 3.000psi (210bar)or temperature above 200°F (95°C), please contact engineering for seal material and hardware specification.

Compare

HS-PRS19

Standard Symmetrical HS-Spring Rod or Piston Seal

For use as either rod or piston seal in slow dynamic and static sealing applications. The HS-spring provides the highest progressive spring load and the smallest deflection range of all spring types, making it ideal for low pressure, vacuum and cryogenic sealing applications. Chamfered seal lips provide for easy installation.

Operating Range

Material	Operating Pressure up to	Maximum Pressure up to	Temperature	Surface Speed up to	Fluid, Media Compatability
Permachem xxxx	5,000psi (350bar) vacuum	10,000psi (700bar)	-328°F to 500°F (-200°C to 260°C)	0.3ft/s (0.1m/s) intermitten	vacuum service, aggressive chemicals, NACE service, chlorine service, cryogenic service, FDA (both contact and non-contact), fugitive emissions, as well as control fluids, hydraulic fluids, dry running in a wide range of gases
Material Permachem xxxx will be selected by AHPSeals to match your operating conditions.
*Important Note: Maximum values above depend on extrusion gap, clearances, seal material, media, temperatures, pressures, surface speed, dynamic running surface finish and working environment. Seals cannot be operated at their upper ratings at the same time. For pressure above 3.000psi (210bar)or temperature above 200°F (95°C), please contact engineering for seal material and hardware specification.

Compare

HS-PRS19C

Symmetrical HS-Spring Rod or Piston Seal with Rounded Seal Lips

For use as either rod or piston seal in slow dynamic and static sealing application. The HS-spring provides the highest progressive spring load and the smallest deflection range of all spring types, making it ideal for low pressure, vacuum and cryogenic sealing applications. The rounded contact surface of the seal lip promotes a thicker lubrication film on the mating sealing surface, leading to less wear and a longer seal life.

Operating Range

Material	Operating Pressure up to	Maximum Pressure up to	Temperature	Surface Speed up to	Fluid, Media Compatability
Permachem xxxx	5,000psi (350bar) vacuum	10,000psi (700bar)	-328°F to 500°F (-200°C to 260°C)	0.3ft/s (0.1m/s) intermitten	vacuum service, aggressive chemicals, NACE service, chlorine service, cryogenic service, FDA (both contact and non-contact), fugitive emissions, as well as control fluids, hydraulic fluids, dry running in a wide range of gases
Material Permachem xxxx will be selected by AHPSeals to match your operating conditions.
*Important Note: Maximum values above depend on extrusion gap, clearances, seal material, media, temperatures, pressures, surface speed, dynamic running surface finish and working environment. Seals cannot be operated at their upper ratings at the same time. For pressure above 3.000psi (210bar)or temperature above 200°F (95°C), please contact engineering for seal material and hardware specification.

Compare

FLA

FLA1

FLB

FLB1

GB

HRO

HS-FL6

HS-FL6

HS-FL7

HS-FL7

HS-PRS19

HS-PRS19C

CONTACT US EXPRESS