Squeeze-type piston seal for use on vertical or no-drift piston applications. Small footprint allows for fitment in confined areas. Economical double-acting hydraulic piston seal.
mineral oil-based fluids, fire-resistant water-based hydraulic fluids including HFA and HFB, sea water, biodegradable fluids, vegetable oils, bio-diesels, and most modern hydraulic fluids
Duralast 4403
5,000psi (350bar)
8,000psi (520bar)
-22°F to 260°F (-30°C to 125°C)
1.6ft/s (0.5m/s)
same as Duralast 4203
Duralast 8166
2,300psi (160bar)
3,800psi (260bar)
-4°F to 392°F (-20°C to 200°C)
3.2ft/s (1.0m/s)
fire-resistant fluids, phosphate esters, mineral oils, greases, and most inorganic acids and chemicals, gasoline and gasoline/alcohol blends, hard vacuum
Duralast 5101
2,300psi (160bar)
3,800psi (260bar)
-22°F to 212°F (-30°C to 100°C)
1.6ft/s (0.5m/s)
mineral-oil based hydraulic fluids, silicone greases, petroleum-based oils, water and alcohols
Duralast 6146
2,300psi (160bar)
3,800psi (260bar)
-30°F to 302°F (-35°C to 150°C)
2.0ft/s (0.7m/s)
excellent heat and oil resistance, including exposure to such oil additives as detergents, anti-oxidants and anti-wear agents
Additional standard materials available: High-performance polyurethanes, NBR (Nitrile), FKM, Viton®, HNBR, EPDM, Aflas®, Hytrel®, Silicone, low- and high-temperature, FDA-compliant seal material grades, PTFE, filled PTFE®, engineered thermoplastics and proprietary specialized Duralast™, Duraloy™, and Permachem™ materials.
Important Note: Maximum values above depend on extrusion gap, clearances, seal material, media, temperatures, pressures, surface speed, dynamic running surface finish and working environment. Seals cannot be operated at their upper ratings at the same time. Pressure ratings can be increased by reducing clearances. For pressure above specified operating pressure, please contact engineering@ahpseals.com
Size Table (Inch)The standard range sizes listed below are the preferred sizes for new design applications. Seals are available for any bore size in 0.001inch increments, including functional range. Additionally, we offer any other seal size as required.
A
Bore Diameter
CS
Cross-Section
D
Groove Diameter
B*
Piston Diameter
Tolerance
L
Groove Width
C
R1
R
Standard Range
Functional Range
Tolerance
D=
B=
D,B
Tol.+0.008/-0
min.
max.
max.
0.312 - 0.564"
0.300 - 0.599"
+0.001/-0
0.097
A - 0.194
A - 0.024
+.000/-.001
0.087
0.045
0.015
0.006
0.565 - 1.499"
0.550 - 1.599"
+0.002/-0
0.148
A - 0.296
A - 0.024
+.000/-.002
0.126
0.050
0.025
0.008
1.500 - 3.124"
0.550 - 12.000"
+0.003/-0
0.217
A - 0.434
A - 0.027
+.000/-.003
0.165
0.070
0.025
0.008
3.125 - 5.249"
1.500 - 18.500"
+0.003/-0
0.305
A - 0.610
A - 0.029
+.000/-.003
0.248
0.100
0.035
0.008
5.250 - 12.499"
3.000 - 26.500"
+0.004/-0
0.414
A - 0.828
A - 0.030
+.000/-.004
0.320
0.130
0.035
0.008
12.500 - 26.599"
5.000 - 26.500"
+0.005/-0
0.483
A - 0.966
A - 0.034
+.000/-.005
0.320
0.130
0.035
0.008
26.600 - 40.124"
10.000 - 50.000"
+0.007/-0
0.552
A - 1.102
A - 0.045
+.000/-.007
0.375
0.150
0.040
0.012
40.125 - 72.500"
20.000 - 72.500"
+0.009/-0
0.748
A - 1.496
A - 0.050
+.000/-.009
0.543
0.170
0.050
0.012
> 72.500"
consult with Ahpseals engineering
* Based on using wear rings. For pressure above 3,800psi or diameter 26,500", please contact engineering for clearances. Surface finish: rod (A) Ra 4-12µin – Static (D,L) Ra max. 32µin. See Technical Info for more specific information.
Size Table (Metric)The standard range sizes listed below are the preferred sizes for new design applications. Seals are available for any bore size in 0.01mm increments, including functional range. Additionally, we offer any other seal size as required.
A
Bore Diameter
Tol. H8
CS
Cross-Section
D
Groove Diameter
Tol. h9
B*
Piston Diameter
Tol. h9
L
Groove Width
C
R1
R
Standard Range
Functional Range
D=
B=
Tol.+0.20/-0
min.
max.
max.
8.00 -14.99
8.00 - 30.00
2.45
A - 4.90
A - 0.60
2.20
1.20
0.40
0.15
15.00 - 39.99
15.00 - 80.00
3.65
A - 7.50
A - 0.60
3.20
1.30
0.60
0.20
40.00 - 59.99
25.00 - 200.00
5.35
A - 10.70
A - 0.70
4.20
1.80
1.00
0.20
60.00 - 199.99
25.00 - 260.00
7.55
A - 15.10
A - 0.74
6.30
2.50
1.30
0.20
200.00 - 259.99
75.00 - 700.00
10.25
A - 20.50
A - 0.76
8.10
3.30
1.80
0.20
260.00 - 674.99
125.00 - 675.00
12.00
A - 24.00
A - 0.86
8.10
3.30
1.80
0.20
675.00 - 999.99
250.00 - 1200.00
14.00
A + 28.00
A + 1.00
9.50
3.80
2.50
0.30
1000.00 - 1850.00
500.00 - 1850.00
19.00
A + 38.00
A + 1.50
13.80
4.20
3.00
0.30
> 1850.00
consult with Ahpseals engineering
* Based on using wear rings. For pressure above 260bar or diameter 675mm, please contact engineering for clearances. Surface finish: bore (A) Ra 0.1-0.3µm – Static (D,L) Ra max. 0.8µm. See Technical Info for more specific information.
