Spring-loaded single-lip rotary shaft seal with non-metallic reinforcing element.
Used for oil and grease retention.
The optimized seal lip design uses a stainless steel garter spring to maintain a constant radial lip load, thus ensuring optimum sealability. The non-metal reinforcement element ensures concentric fitment and increased corrosion resistance over traditional shaft seals. This style is available in a wide range of elastomers and small quantities for repairs and seal replacement and can be shipped in 1 to 3 days. Can be provided for larger and non-standard bore tolerances. For dirty, dusty or polluted environments, our R2 style with additional dust lip should be used.
Size Table (Inch)Standard sizes listed below are preferred sizes for new design applications; however, we offer any other seal size as required. Seals are available for any shaft diameter size in 0.001 inch increments, including functional range.
A
Shaft Diameter
CS
Cross-
D
Bore Diameter
B
Diameter
Tol. +/- 0.010
L
F
C
Chamfer
R1
Radius
Standard Range
Functional Range
Tolerance
section
D=
Tolerance
B=
Tol. +0.010/-0
min.
max.
0.250 - 1.499"
0.250 - 8.000"
+/-0.003
3/8
A + 0.750
+/-.001
A + 0.060
0.387
0.300
0.060
0.020
1.500 - 7.999"
0.500 - 15.000"
+/-0.004
1/2
A + 1.000
+/-.0015
A + 0.080
0.512
0.425
0.090
0.030
8.000 - 15.999"
1.250 - 63.000"
+/-0.005
5/8
A + 1.250
+/-.002
A + 0.080
0.637
0.530
0.130
0.030
16.000 - 30.999"
2.500 - 63.000"
+/-0.006
3/4
A + 1.500
+/-.003
A + 0.080
0.637
0.530
0.150
0.030
31.000 - 63.000"
consult with Ahpseals engineering
*Standard cross-sections (CS) listed and non-standard sizes can be provided for any shaft size up to 63 inches. Seal retaining plat is recommended for split seals or ressures above 3psi. Surface finish: Shaft (A) plunge ground, zero lead, Ra 8-16µin Housing (D,L) Ra 32-63µin. Shaft material hardness min. C45. See Technical Info for more specific information.
Size Table (Metric) Standard sizes listed below are preferred sizes for new design applications; however, we offer any other seal size as required. Seals are available for any shaft diameter size in 0.01 mm increments, including Functional Range.
A
Shaft Diameter (mm)
Tol. h11
CS
Cross-section
D
Bore Diameter
Tol. H8
B
Diameter
Tol. +/- 0.20
L
F
C
Chamfer
R1
Radius
Standard Range
Functional Range
*
D=
B=
Tol. +0.25/-0
min.
max.
6.00 - 39.99
6.00 - 250.00
10.00
A + 20.00
A + 1.50
10.30
8.50
2.30
0.50
40.00 - 129.99
10.00 - 400.00
12.50
A + 25.00
A + 2.00
12.30
10.20
2.70
0.70
130.00 - 259.99
30.00 - 800.00
15.00
A + 30.00
A + 2.00
15.30
12.70
3.50
0.70
300.00 - 799.99
65.00 - 1600.00
20.00
A + 40.00
A + 2.00
20.30
17.00
5.00
0.70
800.00 - 1600.00
consult with Ahpseals engineering
*Standard cross-sections (CS) listed and non-standard sizes can be provided for any shaft size up to 1600mm. Seal retaining plate for split seals or pressures above 3psi recommended. Surface finish: Shaft (A) plunge ground, zero lead, Ra 0.20-0.40µm Housing (D,L) Ra 0.8-1.6µm. Shaft material hardness min. RC45. See Technical Info for more specific information.
