A non-metal seal designed to control leakage in grease-packed bearings.
The springless lip imparts low friction and heat generation. The elastomer outer diameter creates excellent static sealing and compensates for thermal cycling. The small footprint of this seal allows it to be fitted in closed grooves. This style is available in a wide range of elastomers and small quantities for repairs and seal replacement and can be shipped in 1 to 3 days.
Size Table (Inch)Standard sizes listed below are preferred sizes for new design applications; however, we offer any other seal size as required.Seals are available for any shaft diameter size in 0.001 inch increments, including Functional Range.
A
Shaft Diameter
CS
Cross-section
D
Bore Diameter
B Diameter
Tol. +/-0.010
L
F
C
Chamfer
R1
Radius
Standard Range
Functional Range
Tolerance
*
D=
Tolerance
B=
Tol. +0.010/-0
min.
max.
0.200-0.599"
0.200 - 5.000"
+/-0.003
3/16
A + 0.375
+/-.001
A + 0.100
0.210
0.180
0.040
0.020
0.600-1.299"
0.200 - 6.000"
+/-0.003
1/4
A + 0.500
+/-.001
A + 0.150
0.210
0.180
0.050
0.020
1.300 - 2.299"
0.200 - 8.000"
+/-0.003
5/16
A + 0.625
+/-.001
A + 0.160
0.260
0.210
0.050
0.020
2.300 - 3.299"
0.250 - 10.000"
+/-0.003
3/8
A + 0.750
+/-.001
A + 0.170
0.310
0.265
0.060
0.020
3.300 - 7.999"
0.250 - 15.000"
+/-0.004
1/2
A + 1.000
+/-.0015
A + 0.200
0.410
0.350
0.090
0.030
8.000 - 15.999"
0.250 - 63.000"
+/-0.005
3/4
A + 1.500
+/-.002
A + 0.200
0.510
0.430
0.130
0.030
16.000 - 63.000"
consult with Ahpseals engineering
*Standard cross-sections (CS) listed and non-standard sizes can be provided for any shaft size up to 63 inches. Seal retaining plate for ressures above 7 psi recommended. Surface finish: Shaft (A) plunge ground, zero lead, Ra 8-16µin for rubber seal lip, Ra 6-12µin for PTFE seal lip. Housing (D,L) Ra 32-63µin, shaft material hardness 55-65RC. See Technical Info for more specific information.
Size Table (Metric)Standard sizes listed below are preferred sizes for new design applications; however, we offer any other seal size as required. Seals are available for any shaft diameter size in 0.01 mm increments and in standard DIN 3760 sizes, including Functional Range.
A
Shaft Diameter (mm)
Tol. h11
CS
Cross-section
D
Bore Diameter
Tol. H8
B
Diameter Tol. +/- 0.20
L
F
C
Chamfer
R1
Radius
Standard Range
Functional Range
*
D=
B=
Tol. +0.25/-0
min.
max.
5.00 - 14.99
5.00 - 120.00
5.00
A + 10.00
A + 2.50
7.30
6.00
1.00
0.50
15.00 - 40.99
5.00 - 150.00
6.00
A + 12.00
A + 3.50
7.30
6.00
1.30
0.50
41.00 - 59.99
5.00 - 180.00
7.50
A + 15.00
A + 4.00
8.30
6.80
1.50
0.50
60.00 - 84.99
5.00 - 250.00
10.00
A + 20.00
A + 5.00
10.30
8.50
2.30
0.50
85.00 - 129.99
5.00 - 400.00
12.50
A + 25.00
A + 5.00
12.30
10.20
2.70
0.70
130.00 - 259.99
5.00 - 800.00
15.00
A + 30.00
A + 5.00
15.30
12.70
3.50
0.70
300.00 - 799.99
5.00 - 1600.00
20.00
A + 40.00
A + 5.50
20.30
17.00
5.00
0.70
800.00 - 1600.00
consult with Ahpseals engineering
*Standard cross-sections (CS) listed and non-standard sizes can be provided for any shaft size up to 1600mm. Seal retaining plate for pressures above 0.5 bar recommended. Surface finish: Shaft (A) plunge ground, zero lead, Ra 0.20-0.40µm for rubber seal lip - Ra 0.15-0.30µm for PTFE seal lip Housing (D,L) Ra 0.8-1.6µm. Shaft material hardness min. 55-65RC. See Technical Info for more specific information.