The redundant seal lips enable this seal to handle higher pressure and create additional sealing capabilities, especially under flooded conditions. The soft OD eliminates damage to housings manufactured from expensive metals, and the integrated O-ring on the OD of the seal serves as an anti-rotation device and maximizes static sealing between the seal and the bore. Typically used for hydraulic motors, pumps, and transmissions. Small quantities are available in 2-4 days.
Size Table (Inch)Standard sizes listed below are preferred sizes for new design applications; however, we offer any other seal size as required. Seals are available for any shaft diameter size in 0.001 inch increments, including Functional Range.
A
Shaft Diameter
CS
Cross-section
D
Bore Diameter
B
without
wiper lip +/- 0.010
B
with
wiper lip +/- 0.010
L
F
C
R
Standard Range
Functional Range
Tolerance
*
D=
Tolerance
B=
B=
+0.012/-0
+/-0.010
min.
max.
0.315 - 0.999"
0.315 - 5.000"
+/-0.003
1/4
A + 0.500
+/-.001
A + 0.030
A + 0.120
0.325
0.265
0.070
0.020
1.000 - 5.999"
0.315 - 18.000"
+/-0.003
3/8
A + 0.750
+/-.001
A + 0.030
A + 0.120
0.325
0.265
0.085
0.020
6.000 - 15.999"
0.500 - 26.000"
+/-0.004
1/2
A + 1.000
+/-.002
A + 0.035
A + 0.120
0.375
0.310
0.090
0.030
16.000 - 25.999"
0.500 - 26.000"
+/-0.006
5/8
A + 1.250
+/-.003
A + 0.040
A + 0.120
0.512
0.425
0.100
0.030
26.000 - 63.000"
consult with Ahpseals engineering
*Standard cross-sections (CS) listed and non-standard sizes can be provided for any shaft size up to 63 inches.Surface finish: Shaft (A) plunge ground, zero lead Ra 6-12µin - Housing (D,L) Ra max. 32µin - Shaft material hardness 55-65RC. Use of installation tool is highly recommended. See Technical Info for more specific information.
Size Table (Metric)Sizes listed below are preferred sizes for new design applications; however, we offer any other seal size as required.Seals are available for any shaft diameter size in 0.01 mm increments, including Functional Range.
A
Shaft Diameter (mm)
Tol. h11
CS
Cross-section
D
Bore Diameter
Tol. H8
B
without
wiper lip +/- 0.25
B
with
wiper lip +/- 0.25
L
F
C
R
Standard Range
Functional Range
*
D=
B=
B=
Tol. +0.30/-0
Tol.+/-0.20
min.
max.
8.00 - 24.99
8.00 - 127.00
6.00
A + 12.00
A + 0.80
A + 3.00
8.30
6.80
1.80
0.50
25.00 - 139.99
8.00 - 455.00
10.00
A + 20.00
A + 0.80
A + 3.00
8.30
6.80
2.20
0.50
140.00 - 399.99
10.00 - 660.00
12.50
A + 25.00
A + 0.90
A + 3.00
9.50
7.80
2.30
0.70
400.00 - 799.99
10.00 - 660.00
15.00
A + 30.00
A + 1.00
A + 3.00
13.00
10.80
2.50
0.70
800.00 - 1600
consult with Ahpseals engineering
*Standard cross-sections (CS) listed and non-standard sizes can be provided for any shaft size up to 1600 mm. Surface finish: Shaft (A) plunge ground, zero lead Ra 0.15-0.30µm - Housing (D,L) Ra max.0.8µm - Shaft material hardness 55-65RC. Use of installation tool is highly recommended. See Technical Info for more specific information.