Shop Seals | Shop Seals by AHP Seals

Showing 49–60 of 326 results

ADG
ADG
Fluid separation oil seal

The fluid separation oil seal has opposing spring-loaded sealing lips to seal and keep different fluids separated. It has a ribbed OD to accommodate high thermal expansion of the housing. This design can also be used as a combined seal and wiper seal in high contaminated environments.

Compare

Premium medium-pressure single-lip oil seal

Medium-pressure single-lip oil seal with integrated steel reinforcement element

The dynamic seal lip is made of a premium low-friction Duralast™ material to reduce friction, heat build-up, and wear. The rubber-covered OD of the seal creates a tight seal with the housing bore. A retaining device is recommended to hold the seal in place under pressures above 7*psi. This seal is able to accommodate press-in fitment in housings with short axial length. For dirty, dusty or polluted environments, our ASHP style with additional dust lip should be used.

Operating Range

Material	Continuous Pressure	Max. Pressure Spike	Temperature	Surface Speed	Dry-run	PV-Rating
Duralast 8838-LF	60psi (4.1bar)	150psi (10.3bar)	-4 to 392°F (-20 to 200°C)	Up to 2,700 fpm (13.5m/s)	NO	2
Fluoroelastomer (FKM),Viton®	60psi (4.1bar)	150psi (10.3bar)	-4 to 392°F (-20 to 200°C)	Up to 2,300 fpm (11.5m/s)	NO	1.8
Duralast 5117-LF	60psi (4.1bar)	150psi (10.3bar)	-13 to 212°F (-25 to 100°C)	Up to 1,500 fpm (7.5m/s)	NO	1
Nitrile (NBR)	60psi (4.1bar)	150psi (10.3bar)	-13 to 212°F (-25 to 100°C)	Up to 2,400 fpm (12m/s)	NO	0.9

Compare

AHP2

Superior medium-pressure single-lip oil seal

Medium-pressure single-lip oil seal with integrated seal lip support.

A flexible lip design offers better shaft-following ability and reduced lip load over standard seal designs. The dynamic seal lip is made of a premium low-friction Duralast™ material to reduce friction, heat build-up, and wear. The integrated seal lip support allows the seal to handle higher operating pressure. The low friction Duralast™ materials allow a high surface speed. The rubber-covered OD of the seal creates a tight seal with the housing bore. This seal is able to accommodate press-in fitment in housings with short axial length. For dirty, dusty or polluted environments, our ASHP2 style with additional…

Operating Range

Material	Continuous Pressure	Max. Pressure Spike	Temperature	Surface Speed	Dry-run	PV-Rating
Duralast 8838-LF	110psi (7.6bar)	200psi (14bar)	-4 to 392°F (-20 to 200°C)	Up to 6,000 fpm (30m/s)	NO	4
Fluoroelastomer (FKM), Viton®	110psi (7.6bar)	200psi (14bar)	-4 to 392°F (-20 to 200°C)	Up to 5,400 fpm (27m/s)	NO	3.6
Duralast 5117-LF	110psi (7.6bar)	200psi (14bar)	-13 to 212°F (-25 to 100°C)	Up to 1,800 fpm (9m/s)	NO	2
Nitrile (NBR)	110psi (7.6bar)	200psi (14bar)	-13 to 212°F (-25 to 100°C)	Up to 1,400 fpm (7m/s)	NO	1.8

Compare

AHP5

Supreme medium-pressure single-lip rotary shaft seal

Medium-pressure single-lip oil seal with integrated seal lip support and proprietary blends of PTFE bonded onto the dynamic sealing lip.

The combination of integrated lip support, reduced lip load, premium Duralast™ material, and low friction PTFE lip leads to reduced friction, lower heat build up and wear; this in turn results in increased seal life under higher pressures and speeds. This allows the seal to handle higher operating pressure. The rubber-covered OD of the seal creates a tight seal with the housing bore, and the press-in fitment design accommodates housings with short axial space requirements. For dirty, dusty or polluted environments, our ASHP5 style with additional…

Operating Range

Material	Continuous Pressure	Max. Pressure Spike	Temperature	Surface Speed	Dry-run	PV-Rating
Fluoroelastomer (FKM), Viton®/PTFE	150psi (10.3bar)	300psi (20.7bar)	-40 to 400°F (-40 to 200°C)	Up to 7,000 fpm (35m/s)	YES	7
NBR/PTFE	150psi (10.3bar)	300psi (20.7bar)	-40 to 230°F (-40 to 110°C)	Up to 5,000 fpm (25m/s)	YES	5

Compare

AJ
AJ
Heavy duty dirt-/mud-exclusion shaft seal

This is a cartridge seal that is used in muddy or heavy dust environments. The sealing element is protected by a multi-zone labyrinth, providing exceptional contaminate exclusion. The most common application for this seal type is on wheel ends.

Compare

AO

Single lip grease seal

Premium general purpose springless grease seal with integrated metal reinforcement element for press-in fitment in an open housing. Designed to control leakage in grease-packed bearings.

The springless lip imparts low friction and heat generation. The rubber-covered outer diameter creates excellent static sealing without excessive damage to soft alloys. This is an excellent low friction seal for non-pressurized media such as grease or highly viscous fluids.

Operating Range

Material	Continuous Pressure	Max. Pressure Spike	Temperature	Surface Speed
Duralast 8838-LF	3psi (0.2bar)	7psi (0.5bar)	-4 to 392°F (-20 to 200°C)	Up to 7,000 fpm (35m/s)
Duralast 5117-LF	3psi (0.2bar)	7psi (0.5bar)	-13 to 212°F (-25 to 100°C)	Up to 2,600 fpm (13m/s)
Fluoroelastomer (FKM),Viton®	3psi (0.2bar)	7psi (0.5bar)	-4 to 392°F (-20 to 200°C)	Up to 6,000 fpm (30m/s)
Nitrile (NBR)	3psi (0.2bar)	7psi (0.5bar)	-13 to 212°F (-25 to 100°C)	Up to 2,400 fpm (12m/s)

Compare

ARB

Single-lip high-performance rotary shaft seal

Premium spring-loaded single-lip rotary shaft seal with PTFE bonded to the sealing lip.

Optimized seal lip design uses a garter spring to maintain a constant radial lip load, ensuring optimum sealability. The low friction sealing contact area creates lower torque and reduces both seal and shaft wear. The rubber covered OD press fits to create a positive seal with the housing bore and, provides optimal compensation for housings of different thermal expansion, reducing the risk of fretting corrosion in soft alloy or plastic housings. A higher surface roughness of the housing bore is possible with this seal style. For dirty, dusty or polluted environments, use ASRB style…

Operating Range

Material	Continuous Pressure	Max. Pressure Spike	Temperature	Surface Speed	Dry-run	PV-Rating
Fluoroelastomer (FKM), Viton®/PTFE	60psi (4.1bar)	100psi (6.9bar)	-40 to 400°F (-40 to 200°C)	Up to 7,000 fpm (35m/s)	YES	5
NBR/PTFE	60psi (4.1bar)	100psi (6.9bar)	-40 to 230°F (-40 to 110°C)	Up to 3,500 fpm (17.5m/s)	YES	4

Compare

AS

Spring-loaded double-lip oil seal

Premium spring-loaded double-lip oil seal with integrated steel reinforcement element. Used for oil or grease retention.

The optimized seal lip design uses a garter spring to maintain a constant radial lip load, thus ensuring optimum sealability. The rubber covered OD press fits to create a positive seal with the housing bore. The rubber OD also provides optimal compensation for housings of different thermal expansion, reducing possibility of fretting corrosion in soft alloy or plastic housings, and accommodating higher surface roughness of the housing bore. The secondary lip serves both as an effective protection against light airside contaminants and as a lube retainer. Maximum service life can be achieved by…

Operating Range

Material	Continuous Pressure	Max. Pressure Spike	Temperature	Surface Speed
Duralast 8838-LF	3psi (0.2bar)	7psi (0.5bar)	-4 to 392°F (-20 to 200°C)	Up to 5,000 fpm (25m/s)
Duralast 5117-LF	3psi (0.2bar)	7psi (0.5bar)	-13 to 212°F (-25 to 100°C)	Up to 1,800 fpm (9m/s)
Fluoroelastomer (FKM),Viton®	3psi (0.2bar)	7psi (0.5bar)	-4 to 392°F (-20 to 200°C)	Up to 4,000 fpm (20m/s)
Nitrile (NBR)	3psi (0.2bar)	7psi (0.5bar)	-13 to 212°F (-25 to 100°C)	Up to 1,600 fpm (8m/s)

Compare

ASHP

Premium medium-pressure double-lip oil seal

Medium-pressure double-lip oil seal with integrated steel reinforcement element

The dynamic seal lip is made of a premium low-friction Duralast™ material to reduce friction, heat build-up, and wear. The rubber-covered OD of the seal creates a tight seal with the housing bore. The secondary lip serves both effective protection against airside contaminants and as a lube retainer. Maximum service life can be achieved by applying a suitable lubricant between the two sealing lips. A retaining device is recommended to hold the seal in place under pressures above *psi. This seal is able to accommodate press-in fitment in housings with short axial length.

Operating Range

Material	Continuous Pressure	Max. Pressure Spike	Temperature	Surface Speed	Dry-run	PV-Rating
Duralast 8838-LF	60psi (4.1bar)	150psi (10.3bar)	-4 to 392°F (-20 to 200°C)	Up to 2,000 fpm (10m/s)	NO	2
Fluoroelastomer (FKM),Viton®	60psi (4.1bar)	150psi (10.3bar)	-4 to 392°F (-20 to 200°C)	Up to 1,800 fpm (9m/s)	NO	1.8
Duralast 5117-LF	60psi (4.1bar)	150psi (10.3bar)	-13 to 212°F (-25 to 100°C)	Up to 1,200 fpm (6m/s)	NO	1
Nitrile (NBR)	60psi (4.1bar)	150psi (10.3bar)	-13 to 212°F (-25 to 100°C)	Up to 1,000 fpm (5m/s)	NO	0.9

Compare

ASHP2

Superior medium-pressure double-lip oil seal

Medium-pressure double-lip oil seal with integrated seal lip support.

Flexible lip design offers better shaft-following ability and reduced lip load over standard seal designs. The premium low-friction Duralast™ material dynamic seal lip reduces friction, heat build-up, and wear. The secondary lip serves as both an effective protection against airside contaminants and as a lube retainer. Maximum service life can be achieved by applying a suitable lubricant between the two sealing lips. The integrated seal lip support allows the seal to handle higher operating pressure. The low friction Duralast™ materials allow a high surface speed. The rubber-covered OD of the seal creates a tight seal with the…

Operating Range

Material	Continuous Pressure	Max. Pressure Spike	Temperature	Surface Speed	Dry-run	PV-Rating
Duralast 8838-LF	110psi (7.6bar)	200psi (14bar)	-4 to 392°F (-20 to 200°C)	Up to 4,200 fpm (21m/s)	NO	4
Fluoroelastomer (FKM),Viton®	110psi (7.6bar)	200psi (14bar)	-4 to 392°F (-20 to 200°C)	Up to 3,800 fpm (19m/s)	NO	3.6
Duralast 5117-LF	110psi (7.6bar)	200psi (14bar)	-13 to 212°F (-25 to 100°C)	Up to 1,500 fpm (7.5m/s)	NO	2
Nitrile (NBR)	110psi (7.6bar)	200psi (14bar)	-13 to 212°F (-25 to 100°C)	Up to 1,200 fpm (6m/s)	NO	1.8

Compare

ASHP5

Supreme medium-pressure double-lip oil seal

Medium-pressure double-lip oil seal with integrated seal lip support, and proprietary blends of PTFE bonded onto the dynamic sealing lip.

Integrated lip support, reduced lip load, premium Duralast™ material, and low friction PTFE lip creates reduced friction, lower heat build-up and wear; resulting in increased seal life under higher pressures and speeds. This allows the seal to handle higher operating pressure. The rubber-covered OD of the seal creates a tight seal with the housing bore, and the press-in fitment design accommodates housings with short axial space requirements. The secondary lip serves as effective protection against airside contaminants and as a lube retainer. Maximum service life can be…

Operating Range

Material	Continuous Pressure	Max. Pressure Spike	Temperature	Surface Speed	Dry-run	PV-Rating
Fluoroelastomer (FKM), Viton®/PTFE	150psi (10.3bar)	300psi (20.7bar)	-40 to 400°F (-40 to 200°C)	Up to 5,000 fpm (25m/s)	YES	7
NBR/PTFE	150psi (10.3bar)	300psi (20.7bar)	-40 to 230°F (-40 to 110°C)	Up to 2,500 fpm (12.5m/s)	YES	5

Compare

ASRB

Double-lip high-performance rotary shaft seal

Premium spring-loaded double lip rotary shaft seal with proprietary blends of PTFE bonded to the sealing lip.

Optimized seal lip design uses a garter spring to maintain a constant radial lip load, ensuring optimum sealability. The low friction sealing contact area creates lower torque and reduces both seal and shaft wear. This seal handles a maximum pressure of 30psi*. Rubber covered OD press fits to create a positive seal with the housing bore, providing optimal compensation for housings of different thermal expansion, reducing the risk of fretting corrosion in soft alloy or plastic housings. A higher surface roughness of the housing bore may be accommodated. The secondary lip…

Operating Range

Material	Continuous Pressure	Max. Pressure Spike	Temperature	Surface Speed	Dry-run	PV-Rating
Fluoroelastomer (FKM), Viton®/PTFE	60psi (4.1bar)	100psi (6.9bar)	-40 to 400°F (-40 to 200°C)	Up to 7,000 fpm (35m/s)	YES	5
NBR/PTFE	60psi (4.1bar)	100psi (6.9bar)	-40 to 230°F (-40 to 110°C)	Up to 3,500 fpm (17.5m/s)	YES	4

Compare

ADG

AHP

AHP2

AHP5

AJ

AO

ARB

AS

ASHP

ASHP2

ASHP5

ASRB

CONTACT US EXPRESS